EFct (global song-wide multi-effects) page

This page houses settings for global song-wide multi-effects. In addition to track-specific multi-effects, each track has effect sends for global reverb, chorus, delay 1 and delay 2 effects defined on this page.

1. dL.Ln Delay 1 Length

Length of delay in beats (one beat is one quarter note) for delay unit 1. For song BPMs below 80, options will be reduced.

2. dL.Fb Delay 1 Feedback

Feedback ("repeat") strength for delay unit 1.

3. dL.Wd Delay 1 Width

Delay between left and right channel "ping-pong" for delay unit 1

4. d2.Al Delay2 Algorithm

Specifies the algorithm for the second delay unit. Choose between;

• dly (delay); standard delay, identical to delay 1
• spkl (sparkle); applies ring modulation and a one octave pitch shift (up). Depending on the patch this introduces "pleasant" high frequency overtones such "sparkles" and "shimmers".
  

5. dL.Ln Delay 2 Length

Length of delay in beats (one beat is one quarter note) for delay unit 2. For song BPMs below 80, options will be reduced.

6. dL.Fb Delay 2 Feedback

Feedback ("repeat") strength for delay unit 2.

7. dL.Wd Delay 2 Width

Delay between left and right channel "ping-pong" for delay unit 2.

8. Vn.Cr Vinyl Crackle

The amount of emulated vinyl crackle to introduce into the mixer. Negative values for this parameter will only add vinyl crackle while the song is playing.

9. ch.SP Chorus Speed

Speed by which chorus effects unit bounces between chorus time 1 ("ch.t1") and chorus time 2 ("ch.t1").

10. ch.t1 Chorus Time 1

Time delay 1 between original signal and output signal. Chorus unit will bounce between chorus time 1 ("ch.t1") and chorus time 2 ("ch.t2") according to speed ("ch.SP").

11. ch.t2 Chorus Time 2

Time delay 2 between original signal and output signal. Chorus unit will bounce between chorus time 1 ("ch.t1") and chorus time 2 ("ch.t2") according to speed ("ch.SP").

12. ch.AL Chorus Algorithm

Specifies the algorithm that should be used for the chorus FX unit;

• 'Chrs' (chorus) uses a regular stereo chorus algorithm
  
• 'Phas' (phaser) uses a phaser algorithm
  

13. rv.Fb Reverb Feedback

Specifies reverb feedback, impacting how long the "tail" of a sound will be.

14. rv.tM Reverb Time

Specifies reverb time, with longer times sounding more cavernous (for example a cathedral) and short times sounding more compact (for example a studio space).

15. Hal.N North pole Hall sensor mapping

Specifies which parameter the detected south pole magnetic field strength should map to;

• 'Off'; the sensor will not respond to a magnet for this polarity
• 'Fltr'; magnet proximity will cause filter to close for this polarity
• 'FLFO'; magnet proximity will cause filter LFO to modulate filter cut-off frequency for this polarity
• 'PLF.1'; magnet proximity will allow pitch LFO 1 to modulate for this polarity
• 'PLF.2'; magnet proximity will allow pitch LFO 2 to modulate for this polarity
• 'PL.1.2'; magnet proximity will allow pitch LFO 1 and 2 to modulate for this polarity
• 'Vol'; magnet proximity will cause volume to decrease
  
• 'ALF.1'; magnet proximity will allow amplitude LFO 1 to modulate for this polarity
• 'ALF.2'; magnet proximity will allow amplitude LFO 2 to modulate for this polarity
• 'AL.1.2'; magnet proximity will allow amplitude LFO 1 and 2 to modulate for this polarity

16. Hal.S South pole Hall sensor mapping

Specifies which parameter the detected south pole magnetic field strength should map to;

• 'Off'; the sensor will not respond to a magnet for this polarity
• 'Fltr'; magnet proximity will cause filter to close for this polarity
• 'FLFO'; magnet proximity will cause filter LFO to modulate filter cut-off frequency for this polarity
• 'PLF.1'; magnet proximity will allow pitch LFO 1 to modulate for this polarity
• 'PLF.2'; magnet proximity will allow pitch LFO 2 to modulate for this polarity
• 'PL.1.2'; magnet proximity will allow pitch LFO 1 and 2 to modulate for this polarity
• 'Vol'; magnet proximity will cause volume to decrease
  
• 'ALF.1'; magnet proximity will allow amplitude LFO 1 to modulate for this polarity
• 'ALF.2'; magnet proximity will allow amplitude LFO 2 to modulate for this polarity
• 'AL.1.2'; magnet proximity will allow amplitude LFO 1 and 2 to modulate for this polarity